Control Room and PLC Operation
- Monitor the fish meal control room continuously throughout the shift and maintain full attention to the PLC/SCADA displays, alarms, trends and equipment status.
- Start up, operate and shut down plant equipment from the PLC in the approved sequence and only after receiving clearance from the Fish Meal Plant Supervisor and field operators.
- Monitor and control the feeding screws, crusher, cooker, screw press, stick water system, fish oil setting system, dryer, cooler screw conveyor, grinder, conveyors and related auxiliary equipment.
- Observe process values including temperatures, pressures, motor currents, equipment loads, speeds, levels, flow rates, moisture-related indicators and production throughput.
- Adjust authorized set points and operating parameters within approved limits to maintain a steady production flow and required product quality.
- Confirm interlocks, emergency stops and safety systems are healthy before starting or restarting equipment.
- Never bypass alarms, trips, interlocks or safety devices unless formally authorized under an approved procedure.
Alarm Management and Process Response
- Acknowledge alarms promptly, identify the affected equipment or process condition, and take the approved corrective action.
- Immediately inform the Fish Meal Plant Supervisor and relevant field operator of critical alarms, trips, abnormal trends or unsafe conditions.
- Stop or isolate equipment safely when continued operation could cause injury, equipment damage, contamination, fire, blockage or product loss.
- Monitor process trends to identify early signs of overloading, overheating, low flow, high pressure, abnormal levels, motor overload or unstable operation.
- Coordinate with field operators to verify actual plant conditions before restarting tripped equipment or changing critical operating parameters.
- Record alarm events, trips, restarts, downtime, corrective actions and unresolved abnormalities in the control room log.
Production and Quality Control
- Maintain stable cooking, pressing, drying, cooling and grinding conditions according to the approved operating recipe and Supervisor instructions.
- Monitor raw material feed rate and equipment loading to prevent surges, blockages and unnecessary product loss.
- Coordinate with the team and Fish Meal Plant Supervisor when process adjustments are required for moisture, appearance, smell or other product specifications.
- Operate the process to prevent undercooking, overcooking, wet meal, burned meal, contamination and excessive fish oil or stick water losses.
- Keep production batches clearly identified and enter the required batch, product and traceability information accurately.
Communication and Shift Coordination
- Maintain clear communication with the Fish Meal Plant Supervisor, Processing, Maintenance and Quality teams.
- Issue clear instructions to field operators when equipment checks, valve changes, blockage inspections or local confirmations are required.
- Escalate process, mechanical, electrical, instrumentation or automation faults without delay and follow the Supervisor's direction.
- Provide a complete shift handover covering plant status, active alarms, equipment under maintenance, process settings, quality concerns, downtime and pending actions.
- Support plant trials, commissioning activities, recipe optimization and continuous improvement work as assigned.
Control Room Records and Reporting
- Complete hourly operating logs and record key process values, throughput, downtime, alarm events and production figures accurately.
- Prepare or contribute to shift production reports, downtime reports, utility records and incident or abnormality reports.
- Maintain control room logbooks, checklists and electronic records in a clear, timely and traceable manner.
- Report inaccurate instruments, faulty indicators, communication failures or unusual PLC/SCADA behavior immediately.
- Protect system passwords and access rights and do not install software, connect unauthorized devices or alter PLC programs.
Equipment Care and Basic Troubleshooting
- Carry out pre-start control room checks and confirm availability of power, utilities, communication systems and required field clearances.
- Use PLC indications and trends to help identify blockages, overloads, abnormal temperatures, pressure changes, level deviations and equipment trips.
- Perform only authorized operating resets and basic control adjustments; all programming, wiring and instrument repairs must be handled by authorized personnel.
- Coordinate safe isolation and lockout/tagout with the Fish Meal Plant Supervisor and Maintenance team before work begins on affected equipment.
- Keep the control room, operator desk, panels, monitors and records clean, organized and protected from dust, water and unauthorized access.
Safety, Hygiene and Environmental Control
- Follow all site safety procedures for rotating equipment, hot surfaces, steam, electrical systems, chemicals and emergency response.
- Use required personal protective equipment when entering production areas and comply with lockout/tagout requirements.
- Monitor process conditions that may contribute to spills, wastewater, odour, dust, overheating or fire risk and report deviations immediately.
- Follow GMP, hygiene and housekeeping requirements and prevent food/feed safety or cross-contamination risks.
- Report unsafe conditions, incidents, near misses and environmental concerns immediately.
Qualifications & Requirements:
- Diploma or Degree in Electrical Engineering, Instrumentation and Control, Automation, Process Operations, Mechanical Engineering or a related technical field.
- Practical training in PLC/SCADA operation, industrial control systems or process plant operation is required.
- Training in workplace safety, lockout/tagout, HACCP, GMP, fire safety or first aid will be an added advantage.
- Minimum 2-3 years of experience operating a PLC/SCADA-controlled process plant, preferably in fish meal, animal feed, rendering, food processing, oil extraction or continuous thermal processing.
- Practical experience monitoring motors, conveyors, cookers, presses, dryers, tanks, pumps and process instrumentation from a central control room.
- Experience responding to alarms, analyzing process trends, completing shift logs and coordinating with field operators.
- Experience in a newly commissioned plant will be an added advantage.
- Good understanding of PLC/SCADA screens, process alarms, interlocks, trends and equipment status indications.
- Able to read process flow diagrams, operating procedures, equipment tags, control parameters and production records.
- Good observation, concentration, numerical accuracy and problem-solving skills.
- Able to remain attentive throughout the shift and respond calmly and quickly to abnormal conditions.
- Clear communication and strong coordination skills with field operators, Maintenance, Quality and Supervisors.
- Basic understanding of electrical, instrumentation and mechanical systems, with strict respect for authorization limits.
- Honest, responsible, disciplined and able to work with limited supervision.
- Willing to work shifts, weekends and public holidays when required.